 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| www..com MH103A Product Features * +34 dBm IIP3 * RF: 1900 - 2200 MHz * LO: 1600 - 2150 MHz * IF: 50 - 300 MHz * +17 dBm Drive Level * Lead-free/Green SOIC8 package * No External Bias Required The Communications Edge TM Product Information High Dynamic Range UMTS-Band MMIC Mixer Product Description The MH103A is a passive GaAs MESFET mixer that provides high dynamic range performance in a low-cost lead-free/green/RoHS-compliant SOIC-8 package. WJ's MH103A uses patented techniques to realize +34 dBm Input IP3 at an LO drive level of +17 dBm. This single monolithic integrated circuit does not require any external baluns, bias, matching, or decoupling elements. The on-chip diplexer affords good matching on the RF and IF ports. Typical applications include frequency up/down conversion, modulation and demodulation for receivers and transmitters used in 3G UMTS systems. Functional Diagram 4 3 2 1 5 6 7 8 Applications * Mobile Infrastructure Function LO IF RF GND Pin No. 2 5 7 1, 3, 4, 6, 8 Specifications (1) Parameter RF Frequency Range LO Frequency Range IF Frequency Range SSB Conversion Loss Noise Figure Input IP3 Input P1dB LO - RF Isolation LO - IF Isolation RF - IF Isolation Return Loss: RF Port Return Loss: IF Port Return Loss: LO Port LO Drive Level Units MHz MHz MHz dB dB dBm dBm dB dB dB dB dB dB dBm Min Typ Max Comments 1900 - 2200 1600 - 2150 50 - 300 8.2 8.7 +28 +34 +16 21 28 .com 27 37 12 18 15 20 12 +17 9.0 See note 1 See note 2 See note 1, 3 DataShee 1. Test conditions unless otherwise noted: RF / IF = 1900 / 50, 1900 / 200, 2200 / 50, and 2200 / 300 MHz with a low-side LO at +17 dBm in a downconverting application at 25 C. 2. Assumes LO injection noise is filtered at the thermal noise floor, -174 dBm/Hz, at the RF, IF, and Image frequencies. 3. IIP3 is measured with f = 1 MHz with RFin = 0 dBm / tone. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature LO Power Input IF .com / RF Power -40 to +85 C -65 to +100 C +20 dBm +20 dBm Ordering Information Part No. MH103A* MH103A-G MH103A-PCB Rating Description High Dynamic Range UMTS-band MMIC Mixer (lead-tin SOIC-8 package) High Dynamic Range UMTS-band MMIC Mixer (lead-free/green/RoHS-compliant SOIC-8 package) Fully-Assembled Mixer Application Board Specifications and information are subject to change without notice Operation of this device above any of these parameters may cause permanent damage. * This package is being phased out in favor of the green package type which is backward compatible for existing designs. WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 1 of 5 August 2005 DataSheet 4 U .com www..com MH103A Input IP3 vs RF Frequency Low-side Downconversion, LO = +15 dBm, 25 C The Communications Edge TM Product Information High Dynamic Range UMTS-Band MMIC Mixer Typical Performance Plots: Low-side Downconversion Input IP3 vs RF Frequency Low-side Downconversion, LO = +17 dBm, 25 C Input IP3 vs RF Frequency Low-side Downconversion, LO = +19 dBm, 25 C 38 In p u t IP 3 (d B m ) In p u t IP 3 (d B m ) 36 34 32 30 28 1800 1900 2000 2100 2200 38 In p u t IP 3 (d B m ) IF = 50 MHz IF = 200 MHz IF = 300 MHz IF = 150 MHz IF = 250 MHz 36 34 32 30 28 1800 1900 2000 2100 2200 38 36 34 32 30 28 1800 1900 2000 2100 2200 IF = 50 MHz IF = 200 MHz IF = 300 MHz IF = 150 MHz IF = 250 MHz IF = 50 MHz IF = 200 MHz IF = 300 MHz IF = 150 MHz IF = 250 MHz RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, LO = +15 dBm, 25 C RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, LO = +17 dBm, 25 C RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, LO = +19 dBm, 25 C 10 C o n v e rs io n L o s s (d B ) C o n v e rs io n L o s s (d B ) 9 8 7 6 5 1800 10 9 8 7 6 5 1800 C o n v e rs io n L o s s (d B ) 10 9 8 7 6 5 1800 t4U.com IF = 50 MHz IF = 200 MHz IF = 300 MHz 1900 IF = 150 MHz IF = 250 MHz IF = 50 MHz IF = 200 MHz IF = 300 MHz 1900 IF = 150 MHz IF = 250 MHz IF = 50 MHz IF = 200 MHz IF = 300 MHz 1900 IF = 150 MHz IF = 250 MHz DataShee 2200 2000 2100 RF Frequency (MHz) 2200 2000 2100 2200 RF Frequency (MHz) .com 2000 2100 RF Frequency (MHz) IF Return Loss LO = +17 dBm, 25 C RF Return Loss LO = +17 dBm, 25 C LO Return Loss LO = +17 dBm, 25 C 0 R F R e tu rn L o s s (d B ) IF R e tu rn L o s s (d B ) RF = 1900 MHz 0 RF = 2000 MHz RF = 2200 MHz 0 IF = 200 MHz IF = 300 MHz -10 -20 -30 -40 50 -5 -10 -15 -20 1700 L O R e tu rn L o s s (d B ) IF = 50 MHz -5 -10 -15 -20 1600 100 150 200 250 IF Frequency (MHz) 300 1800 1900 RF Frequency (MHz) 2000 1800 2000 LO Frequency (MHz) 2200 L-R Isolation Low-side Downconversion L-I Isolation Low-side Downconversion 40 L -R Is o la tio n (d B ) 30 20 10 -40C 0 1600 +25C +85C 2200 L -I Is o la tio n (d B ) 40 30 20 10 0 1600 -40C +25C +85C 1800 2000 LO Frequency (MHz) 1800 2000 LO Frequency (MHz) 2200 .com Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 2 of 5 August 2005 DataSheet 4 U .com www..com MH103A Input IP3 vs RF Frequency Low-side Downconversion, IF = 50 MHz, LO = +17 dBm The Communications Edge TM Product Information High Dynamic Range UMTS-Band MMIC Mixer Typical Performance Plots over Temperature: Low-side Downconversion Input IP3 vs RF Frequency Low-side Downconversion, IF = 150 MHz, LO = +17 dBm Input IP3 vs RF Frequency Low-side Downconversion, IF = 200 MHz, LO = +17 dBm 40 In p u t IP 3 (d B m ) In p u t IP 3 (d B m ) 38 36 34 32 30 1800 -40C +25C +85C 40 In p u t IP 3 (d B m ) 38 36 34 32 -40C 1900 2000 2100 RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, IF = 50 MHz, LO = +17 dBm 40 38 36 34 32 30 1800 -40C +25C +85C 2200 +25C +85C 2200 2200 30 1800 1900 2000 2100 RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, IF = 150 MHz, LO = +17 dBm 1900 2000 2100 RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, IF = 200 MHz, LO = +17 dBm 10 C o n v e rs io n L o s s (d B ) C o n v e rs io n L o s s (d B ) 9 8 7 6 5 1800 -40C +25C +85C 2200 10 9 8 7 6 5 1800 -40C 1900 2000 +25C 2100 +85C 2200 C o n v e rs io n L o s s (d B ) 10 9 8 7 6 5 1800 -40C +25C +85C 2200 t4U.com DataShee 1900 2000 2100 RF Frequency (MHz) 1900 2000 2100 RF Frequency (MHz) RF Frequency (MHz) .com Input IP3 vs RF Frequency Input IP3 vs RF Frequency Low-side Downconversion, IF = 250 MHz, LO = +17 dBm Low-side Downconversion, IF = 300 MHz, LO = +17 dBm 40 In p u t IP 3 (d B m ) In p u t IP 3 (d B m ) -40C +25C +85C 2200 38 36 34 32 30 1800 40 38 36 34 32 30 1800 -40C +25C +85C 2200 1900 2000 2100 RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, IF = 250 MHz, LO = +17 dBm 1900 2000 2100 RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion, IF = 300 MHz, LO = +17 dBm 10 C o n v e rs io n L o s s (d B ) 9 8 7 6 5 1800 -40C +25C +85C 2200 C o n v e rs io n L o s s (d B ) 10 9 8 7 6 5 1800 -40C +25C +85C 2200 1900 2000 2100 RF Frequency (MHz) 1900 2000 2100 RF Frequency (MHz) .com Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 3 of 5 August 2005 DataSheet 4 U .com www..com MH103A The Communications Edge TM Product Information High Dynamic Range UMTS-Band MMIC Mixer MH103A (SOIC-8 Package) Mechanical Information This package may contain lead-bearing materials. The plating material on the leads is SnPb. Application Circuit (MH103A-PCB) LO PIN 2 PIN 7 RF IF PIN 5 Notes: 1. All other pins on mixer are grounded. 2. Circuit board material: .014" FR-4, 4 layers, .062" total thickness 3. Blocking capacitors are required on the ports (pins 2, 5, 7) if any dc signal is present. Outline Drawing Product Marking The component will be marked with an "MH103A" designator followed by an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the "Application Notes" section. t4U.com DataShee .com ESD / MSL Information ESD Classification: Value: Test: Standard: Class 1B Passes 500V to <1000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class III Passes 500 V to <1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 Level 3 at +235 C convection reflow JEDEC Standard J-STD-020B Mounting Configuration / Land Pattern ESD Classification: Value: Test: Standard: MSL Rating: Standard: Functional Pin Layout Pin 1 2 3 4 5 6 7 8 Function Ground LO Port Ground Ground IF Port Ground RF Port Ground .com Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 4 of 5 August 2005 DataSheet 4 U .com www..com MH103A The Communications Edge TM Product Information High Dynamic Range UMTS-Band MMIC Mixer MH103A-G (Lead-Free Package) Mechanical Information This package is lead-free/green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both lead-free (maximum 260C reflow temperature) and lead (maximum 245C reflow temperature) soldering processes. Application Circuit (MH103A-PCB) LO PIN 2 PIN 7 RF IF PIN 5 Notes: 1. All other pins on mixer are grounded. 2. Circuit board material: .014" FR-4, 4 layers, .062" total thickness 3. Blocking capacitors are required on the ports (pins 2, 5, 7) if any dc signal is present. Outline Drawing Product Marking The component will be marked with an "MH103A-G" designator followed by an alphanumeric lot code on the top surface of the package. t4U.com Tape and reel specifications for this part are located on the website in the "Application Notes" section. .com ESD / MSL Information ESD Classification: Value: Test: Standard: ESD Classification: Value: Test: Standard: MSL Rating: Standard: Class 1B Passes 500V to <1000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class III Passes 500 V to <1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 Level 2 at +260 C convection reflow JEDEC Standard J-STD-020B Land Pattern / Mounting Configuration Functional Pin Layout Pin 1 2 3 4 5 6 7 8 Function Ground LO Port Ground Ground IF Port Ground RF Port Ground .com Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 5 of 5 August 2005 DataSheet 4 U .com |
Price & Availability of MH103A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |